All Calculators
Every YardMath calculator in one place, grouped by project. All 22 tools are free, run entirely in your browser, and show the formula behind every result — so you can check the arithmetic, change the waste allowance, or hand the numbers straight to your supplier. Your inputs travel in the page link, so a calculation you did on Tuesday is still there on Saturday.
The tools fall into five groups. Concrete and structure covers everything you pour, frame or reinforce. Floors, walls and rooms covers the interior — measuring, finishing and comfort. Outside covers the yard: lawns, beds, stone and soil. Roofs and decks covers the top of the house and the back of it. And the last group is the driveway and the path to it.
Concrete and structure
The heaviest decisions on a job site are the ones that arrive by truck. These tools size pours, framing and steel so the order is right the first time — too little means a second delivery fee, too much means material you paid to haul away.
Concrete Calculator
Cubic yards, 40/60/80 lb bags and cost for slabs, footings and columns. Handles rectangular slabs, round columns, continuous footings and a custom area, with a PSI guide by project type so the strength matches the job.
Concrete Block Calculator
8×16 in blocks, mortar bags and core-fill concrete for any wall. One block covers 0.8889 sq ft of wall face, one 80 lb bag of mortar lays about 33 blocks, and the core-fill figure tells you the maximum concrete if every core is filled.
Rebar Calculator
#3, #4 and #5 bars for slabs and footings: bars each way, total linear feet, weight in pounds and the number of 20-ft bars to buy. Spacing from 12 to 24 in on center, with the edge bars counted in both directions.
Lumber Calculator
Studs, plates, total linear feet and board feet for wall framing. Studs are counted at your spacing plus one end stud, plates are always three runs — one bottom plate and a double top plate — and board feet use the actual dressed size of the board.
Floors, walls and rooms
Interior work starts with one number — the area — and then asks what goes on it. These tools walk that chain: measure the room, cover the floor, finish the walls, and keep the room comfortable.
Square Footage Calculator
Add rooms, split L-shaped spaces and get total square feet or square meters. The starting point for almost every interior project on this site — measure once here, then feed the same number into flooring, tile or paint.
Flooring Calculator
Boxes, underlayment rolls and cost, with a waste slider for your layout. Covers plank and tile flooring by box coverage, and tells you how many transition strips the room needs.
Tile Calculator
Tile count, grout bags and waste for any tile size and joint width. Uses the true laying pitch — tile plus grout joint — so the count matches what you will actually lay, not the nominal tile size.
Paint Calculator
Gallons needed per coat for walls and ceilings, minus doors and windows. Walks the perimeter, subtracts the openings, and returns gallons per coat with ceiling and primer options.
Drywall Calculator
Sheets, screws, tape and joint compound for rooms, including ceilings. Sheets by board size, doors and windows deducted, and the finishing materials listed alongside the boards.
Wallpaper Calculator
Rolls needed for any wall, minus doors and windows, with pattern-repeat waste built in. One single roll covers about 28 sq ft after pattern matching; double rolls cover about 56 sq ft.
Insulation Calculator
Bags needed for attics and walls by R-value, with installed thickness and cost. Coverage per bag comes from manufacturer charts — R-13 covers about 88.75 sq ft per bag, R-30 about 31.25.
BTU Calculator
What size air conditioner do I need? BTUs and tons for any room, starting at 20 BTU per square foot and adjusting for sun exposure, ceiling height, people and kitchens.
Outside: lawns, beds, stone and soil
Yard materials share one volume shortcut — (square feet × inches of depth) ÷ 324 = cubic yards — but they are sold differently: bags, tons, pallets or truckloads. These tools speak the language of the yard where you buy it.
Mulch Calculator
Cubic yards and bags for rectangular, circular and ring-shaped beds. Handles 2 and 3 cu ft bags plus bulk yards, with a ring mode for mulching around trees.
Gravel Calculator
Yards, tons and bags by stone type, from driveways to decorative beds. Stone-type density turns volume into tonnage, because gravel is sold by the ton.
Topsoil Calculator
Cubic yards, 40 lb bags and tons of topsoil for lawns and garden beds. Depth of loam in, yards and truckload weight out.
Sod Calculator
Rolls, pallets and cost for any lawn size. One roll covers 10 sq ft, one pallet covers 500 sq ft, and the waste allowance covers the cutting around beds, paths and sprinkler heads.
Sand Calculator
Cubic yards, tons and 50 lb bags for patios, paver bases and play areas. Sand runs about 2,700 lb per cubic yard, and one 50 lb bag is about half a cubic foot.
Fence Calculator
Posts, rails, boards and concrete bags for privacy fences of any length. Gate posts are added, pickets are counted at their true pitch, and every post gets its concrete.
Roofs and decks
The top of the house and the back of it. Both tools start from a footprint and a slope or a size, and both return a shopping list you can hand to the store — bundles and boards, not just square feet.
Roofing Calculator
Roof area by pitch, squares, shingle bundles, underlayment rolls and drip edge. The pitch factor turns a flat footprint into true roof area, and three bundles make one square.
Deck Calculator
Decking boards, joists, posts, screws and concrete for any deck size. Built for 5.5 in boards with a 1/8 in gap and 16 in joist spacing, with a waste slider for cuts and mistakes.
Deck Stain Calculator
Gallons of stain for new wood or recoats, by coats and coverage. New wood takes about 200 sq ft per gallon, recoats about 300, and two coats is the standard for a new deck.
Driveways and paths
The last stretch of the project — the surface you drive and walk on. One tool, two materials, and the same depth math as the rest of the yard.
Asphalt Calculator
Tons, 50 lb cold-patch bags and cost for driveways and overlays. Asphalt runs about 145 lb per cubic foot; hot mix is ordered by the ton, cold patch comes in 50 lb bags for small repairs.
Before you buy: what the numbers are (and are not)
Every result on this site is an estimate for planning — a careful one, but an estimate all the same. Formulas are tested against hand-worked examples, coverage figures come from manufacturer datasheets, and densities come from quarry and extension-service averages, but your job site is not a datasheet. A base that is uneven, a wall that is out of square, or a supplier whose bags run a little light will all move the real number a few percent in either direction. That is what the waste allowance is for: it is not padding, it is the margin that absorbs the difference between the drawing and the dirt.
Confirm quantities with your supplier before you pay, especially on the big orders — truckloads of concrete, pallets of sod, squares of shingles — where a rounding error costs real money. And anything load-bearing, below grade, or attached to a permit is a conversation with a contractor or engineer, not a calculator: use the numbers here to budget and plan the order, then confirm the specification with someone who has actually seen the site. Prices are national planning ranges checked November 2026, never quotes, because regional pricing swings hard with season, distance from the plant, and the price of oil.
How to use any calculator on this site
Every tool works the same way. Measure the space with a tape measure — length, width, and depth or thickness where it applies — and type the numbers in. Results update as you type: volume, bag count, tonnage and cost, with a waste allowance slider set to the right default for your project. The quick answer at the top of each page is the one-sentence version; the worked example below the calculator shows the arithmetic step by step so you can check it by hand.
Three conventions hold across all 22 tools. First, quantities are shown exact and then rounded: the volume or area you need is printed to two decimals, and the things you actually buy — bags, boxes, boards, gallons, tons — are rounded up to whole units, because nobody sells 0.61 of a bag. Second, waste is a choice, not a constant: each tool starts at a sensible default and always shows the raw number next to the adjusted one, so you can see exactly what the allowance is costing you. Third, cost lines round the purchase quantity the way suppliers bill it, and every price field is optional — leave a price blank and the cost rows simply disappear.
Your numbers travel in the page link. Change an input and the URL updates, so you can bookmark a calculation, share it with a contractor, or paste it into a quote request. Switching units is one tap — feet and inches, or meters and centimeters — and the site remembers your preference on your own device. Nothing you type is uploaded anywhere: every calculator runs entirely in your browser.
If you are not sure which tool you need, start on the home page — it maps each project to its calculator — or work through the groups above in project order: measure, pour or frame, cover, and finish. And if a result ever looks wrong, the fastest check is the worked example on that page: redo it by hand with the same inputs, and the calculator should match you exactly.