Sand Calculator — Cubic Yards, Tons & 50 lb Bags
Enter your area and depth and get cubic yards, tons and 50 lb bags — sand runs about 2,700 lb per cubic yard, with a 10% waste allowance.
A 10×10 ft area, 3 in deep needs 0.93 cu yd of sand — about 1.25 tons (before waste).
Sand calculator
Results update as you type. Your numbers are saved in the page link, so you can bookmark or share them.
Includes a 10% waste allowance for compaction and spillage — adjust with the slider. Bag counts always round up to whole bags. Bulk sand is usually sold by the ton or the cubic yard; bags are the expensive way to buy more than a few cubic feet.
How the sand calculator works
This sand calculator converts the dimensions of your project area into the three quantities you actually need to order: cubic yards, tons, and 50 lb bags. Sand is sold differently depending on where you buy it — landscape yards sell by the cubic yard or by weight in tons, while hardware stores sell bagged sand by the pound — so the calculator gives you all three formats from the same numbers.
You enter four inputs. Length and width are the dimensions of the area you want to cover, measured in feet. Depth is how thick the sand layer will be, entered in inches, since project depths like 2, 3, or 4 inches are easier to think in than fractions of a foot. Waste allowance is a percentage added on top of your calculated volume to cover spillage, uneven subgrade, compaction, and the sand that inevitably stays in the wheelbarrow or bag. The default is 10%, which suits most above-ground applications like play areas and paver bedding.
The math, step by step
cubic feet = length (ft) × width (ft) × depth (in) ÷ 12cubic yards = cubic feet ÷ 27
tons = cubic yards × 1.35 (about 2,700 lb per cubic yard)
50 lb bags = cubic feet ÷ 0.5 (round up)
- One 50 lb bag: about 0.5 cu ft of sand, so two bags make roughly one cubic foot.
- Density: sand runs 2,600–2,800 lb per cubic yard depending on type and moisture; this calculator uses 2,700 lb.
- Compaction: a paver base is screeded loose then compacted, which settles it about 10–15% — the 10% waste allowance covers that.
- Depth shortcut: (square feet × inches of depth) ÷ 324 = cubic yards — the same shortcut the mulch and topsoil pages use.
The math runs in four steps. First, convert depth to feet by dividing inches by 12, then multiply length × width × depth in feet to get cubic feet — that's the actual volume of sand the space holds. Second, divide cubic feet by 27 to get cubic yards, because one cubic yard is a box 3 ft on each side, or 27 cubic feet. Third, convert volume to weight: one cubic yard of dry sand weighs about 2,700 lb, so multiply cubic yards by 1.35 to get tons. Fourth, work out bags: one 50 lb bag holds roughly 0.5 cubic feet, so divide total cubic feet by 0.5 and round up to a whole bag — you can't buy half a bag.
A note on the weight conversion: the 2,700 lb per cubic yard figure is an average for dry sand. Densities across common sand types run 2,600–2,800 lb per cubic yard, so your delivered tonnage may vary slightly either way. If your supplier sells by weight, ask what density they use for billing — wet sand can weigh noticeably more than dry sand, and that affects the price on a ton-based order.
The waste allowance matters more than most people expect. Sand is fine and shifts easily, so it settles into any low spots in your subgrade rather than sitting evenly on top. A paver base laid over ground that isn't perfectly flat can consume several extra cubic feet before you ever place a stone. When spreading by wheelbarrow, some sand always stays behind in the barrow, the shovel, and the yard. Ordering exactly the calculated amount is the most common way DIYers end up short on a Saturday morning, when a second trip to the store costs an hour or more. The 10% default is a sensible buffer for typical projects; drop it lower only if you're covering a smooth, compacted, level surface, and raise it toward 15–20% if the ground is soft, uneven, or the sand will be compacted heavily.
Two practical tips. Measure the area at the surface you're covering, and measure depth where the sand will actually be spread — not at the highest point of the site. And when ordering loose sand by the yard or ton, round your final number up to the supplier's delivery increment; most trucks and loaders move in half-yard or quarter-ton steps.
Worked example: a 10 × 10 ft area, 3 in deep
Here's the worked example for a 10×10 ft area at 3 inches deep, using the default 10% waste allowance.
- Area: 10 ft × 10 ft = 100 sq ft of surface to cover.
- Cubic feet: multiply area by depth in feet. Depth of 3 in ÷ 12 = 0.25 ft, so 100 × 3 ÷ 12 = 25 cubic feet of sand needed.
- Cubic yards: 25 ÷ 27 = 0.93 cu yd.
- Tons: 0.93 cu yd × 1.35 = 1.25 tons, using the average dry-sand weight of 2,700 lb per cubic yard.
- Bags: one 50 lb bag holds about 0.5 cu ft, so 25 ÷ 0.5 = 50 bags, with no rounding needed in this case.
- Adding the default 10% waste allowance: 0.93 × 1.10 ≈ 1.02 cu yd, so ordering a full cubic yard (or the 1.25-ton equivalent) covers the base volume plus spillage and settling.
- Cost check: at the default price of $45 per ton, 1.25 tons × $45 = $56.25. This is a planning figure using the default price, not a quote — actual delivered prices vary by region and supplier.
So the practical answer for a 10×10 ft sandbox or paver bed at 3 in deep is about 0.93 cubic yards, roughly 1.25 tons, or 50 bags of 50 lb sand.
Quick reference tables
Speed sheetThe table below shows material quantities for three common project sizes, using the same formula as the calculator: volume in cubic feet, then cubic yards, tons at 2,700 lb per cubic yard, and 50 lb bags
The table below shows material quantities for three common project sizes, using the same formula as the calculator: volume in cubic feet, then cubic yards, tons at 2,700 lb per cubic yard, and 50 lb bags.
| Project | Depth | Cubic Feet | Cubic Yards | Tons | 50 lb Bags |
|---|---|---|---|---|---|
| 10×10 ft area | 3 in | 25 | 0.93 | 1.25 | 50 |
| 20×10 ft area | 4 in | 66.7 | 2.47 | 3.33 | 134 |
| 12×12 ft paver base | 2 in | 24 | 0.89 | 1.20 | 48 |
Sand isn't interchangeable, so match the type to the job before you order. The table below summarizes the four common types and what each is used for; densities across these types run 2,600–2,800 lb per cubic yard, which is why the calculator uses the 2,700 lb average.
| Sand Type | Characteristics | Typical Uses |
|---|---|---|
| Concrete sand | Coarse | Pavers and mixes |
| Mason sand | Fine | Mortar and leveling |
| Play sand | Washed | Sandboxes |
| Fill sand | Cheapest | Grading |
What sand costs
Sand pricing varies more by region than most materials, so treat these as national planning ranges checked November 2026 — never quotes. Loose sand sold in bulk by the ton commonly runs near $45 per ton as a planning baseline, which is the default price the calculator uses. Bagged sand costs more per unit volume than bulk, but it's the practical choice for small jobs: at 50 lb per bag, a project like the worked example needs 50 bags, which you can carry home in a pickup over a couple of trips.
Bulk delivery makes sense once your tonnage climbs past what bags can handle. The 20×10 ft area at 4 in deep needs 3.33 tons — well past the point where hauling bags one at a time is worth it. Delivery fees, minimum loads, and local sand availability push the final invoice around, so get a delivered price from a local supplier and compare it against the planning range before ordering.
Frequently asked questions
How much sand do I need for a 10×10 ft area at 3 inches deep?
A 10×10 ft area at 3 in deep holds 25 cubic feet of sand, which works out to 0.93 cubic yards or about 1.25 tons using the 2,700 lb per cubic yard average. That's also 50 bags of 50 lb sand. With the default 10% waste allowance, order roughly a full cubic yard so settling and spillage don't leave you short.
How many 50 lb bags of sand are in a cubic yard?
One cubic yard is 27 cubic feet, and a 50 lb bag holds about 0.5 cubic feet. That means about 54 bags per cubic yard. For the 10×10 ft, 3 in example, 25 cubic feet works out to exactly 50 bags. Bags cost more per cubic foot than bulk sand, so most projects over a cubic yard are cheaper delivered loose.
How much does a cubic yard of sand weigh?
Dry sand averages about 2,700 lb per cubic yard, which is why the calculator multiplies cubic yards by 1.35 to get tons. Actual weights range from 2,600 to 2,800 lb per cubic yard depending on the sand type and moisture content. Wet sand weighs more than dry, so if your supplier bills by weight, ask what density they use.
Should I buy bagged sand or bulk sand?
For small jobs, bags are easier: no delivery fee, no pile in the driveway, and you can buy them as needed. A 10×10 ft area at 3 in deep takes 50 bags — manageable. Once you're past a ton or so, bulk delivery usually wins on price per cubic yard and saves your back. The 20×10 ft at 4 in example needs 3.33 tons, firmly bulk territory.
What type of sand should I use for a paver base?
Concrete sand is the standard choice for paver bedding — its coarse texture drains well and locks the stones in place. Mason sand is fine and better suited to mortar and leveling work, and it can shift under pavers over time. Fill sand is cheapest but not stable enough for a finished paver surface. For a 12×12 ft paver base at 2 in, plan on 0.89 cubic yards, or 48 bags.
What depth of sand do I need?
It depends on the job. Paver bedding typically uses a shallow layer — the 2 in example for a 12×12 ft base is representative. Play areas and sandboxes run deeper, with the 3 in example being a common working depth. Deeper layers cost proportionally more, since volume scales directly with depth: doubling depth from 3 in to 6 in on the same area doubles your tonnage.
Why does the calculator include a waste allowance?
Sand settles into low spots, spills during handling, and sticks to wheelbarrows and bags. A level, compacted subgrade wastes little, but uneven ground can consume several extra cubic feet before you place anything on top. The default 10% covers typical conditions. Raise it toward 15–20% for soft or badly uneven ground or heavily compacted fills; on smooth, level surfaces you can drop it lower.
How much does sand cost?
Treat pricing as a planning exercise, not a quote: these are national planning ranges checked November 2026. The calculator's default baseline is $45 per ton for bulk sand. On that basis, the worked example — 1.25 tons — comes to $56.25 before delivery. Bagged sand runs higher per cubic foot, and delivered bulk prices vary by region, so get a local delivered quote before committing to an order.
Assumptions and limitations
- Depth is entered in inches and converted to feet by dividing by 12 before the volume calculation.
- One cubic yard equals 27 cubic feet.
- Sand weighs an average of 2,700 lb per cubic yard, so tons = cubic yards × 1.35.
- One 50 lb bag of sand holds approximately 0.5 cubic feet, and bag counts are rounded up to whole bags.
- Sand densities vary from 2,600–2,800 lb per cubic yard depending on type and moisture, so tonnage is an estimate.
- A 10% waste allowance is applied by default; the worked example shows the base volume plus allowance for ordering.
Sources
- Quikrete — quikrete.com
- CEMEX — cemex.com
- Vulcan Materials Company — vulcanmaterials.com
- National Stone, Sand & Gravel Association — nssga.org
Last reviewed: November 20, 2026, by the YardMath Editorial Team. Formulas re-checked against manufacturer datasheets; national price ranges refreshed quarterly.