Concrete Block Calculator — Blocks, Mortar & Fill
Enter your wall size and get 8×16 in blocks, mortar bags and core-fill concrete — with a 5% waste allowance built in.
A 20×8 ft wall needs 189 concrete blocks and 6 bags of mortar.
Concrete block calculator
Results update as you type. Your numbers are saved in the page link, so you can bookmark or share them.
Includes a 5% waste allowance — adjust with the slider. Blocks always round up to whole blocks. Core fill assumes every core is filled; most walls fill only the cores with rebar, so treat it as the maximum.
How the concrete block calculator works
This calculator tells you three things for any concrete block wall: how many 8×16 in blocks to buy, how many 80 lb bags of mortar you need to set them, and how much concrete it takes to fill the cores if your design calls for solid fill. Enter the wall length and height in feet, and the calculator does the rest, including a 5% waste allowance on the block count.
The inputs are straightforward. Wall length is the horizontal run of the wall in feet. Wall height is the vertical distance from the bottom of the wall to the top course. The waste allowance is set to 5% by default and covers blocks that arrive cracked, get cut wrong, or break during handling — you can adjust it if your supplier has a higher breakage rate or if your wall needs a lot of cut blocks around corners and openings. The block price input defaults to $2.50 per block so you can get a rough material cost for the blocks themselves.
The math, step by step
wall area = length (ft) × height (ft)blocks = wall area ÷ 0.8889 × 1.05 (round up)
mortar bags = blocks ÷ 33 (round up)
core fill = blocks × 0.35 cu ft (if every core is filled)
- Block face: a standard 8 × 8 × 16 in block covers 8 × 16 in = 0.8889 sq ft of wall face, so about 1.125 blocks cover one square foot.
- Mortar: one 80 lb bag of mortar lays about 33 standard blocks — a 3/8 in joint is assumed.
- Core fill: filling every core takes about 0.35 cu ft of concrete per block; most walls only fill the cores with rebar in them, so treat the full-fill number as the maximum.
- Waste: 5% covers broken blocks and cuts; add more for walls with many openings or corners.
Here is the math, step by step. A standard 8×16 in block covers 128 square inches, which works out to 0.8889 square feet of wall face per block. The calculator takes your wall area — length times height — and divides it by 0.8889 to get the raw block count for a single course-per-face layout. It then multiplies by the waste factor (1.05 at the default 5%) and rounds up to the next whole block, because you cannot buy a fraction of a block.
Mortar is estimated next. An 80 lb bag of mortar mix typically lays about 33 blocks when you're buttering both beds and the vertical joints at a standard 3/8 inch joint thickness. So the calculator divides the block count by 33 and rounds up to whole bags. If your wall uses half blocks for the top course or needs extra mortar for heavy cutting, you may go through a bag faster than the estimate suggests.
Core fill is the last piece. Each standard block has two cores, and filling every core in a block takes roughly 0.35 cubic feet of concrete or grout. Multiply the block count by 0.35 to get cubic feet, then divide by 27 to convert to cubic yards, which is how ready-mix concrete is usually ordered. This number assumes every core is filled. Many walls only need fill in bond beam courses or around rebar-reinforced cells, so fill only what your plan calls for.
Two practical tips. First, do not skip the waste allowance. Blocks chip in transit and on site, and cut sections around doors, windows, and corners mean offcuts you can't reuse. Ordering exactly the bare count is the fastest way to end a job one course short. Second, before ordering ready-mix fill, confirm with your mason which cores actually get filled — a partially filled wall can cut the concrete order by half or more, and ready-mix suppliers often have minimum load charges that make a small fill order expensive.
Worked example: a 20 × 8 ft wall
A 20 ft long, 8 ft high wall is the most common size for a residential foundation or privacy wall, so we'll work it end to end.
- Wall area: 20 × 8 = 160 square feet.
- Blocks before waste: 160 ÷ 0.8889 = about 180 blocks for one face of the wall with no allowance for breakage or cutting.
- Add the 5% waste allowance: 180 × 1.05 = about 189. Apply the ceiling and you order 189 concrete blocks.
- Mortar: divide the block count by the coverage of an 80 lb bag. 189 ÷ 33 = 5.7, which rounds up to 6 bags of mortar.
- Core fill, if every core is filled: 189 × 0.35 = 66.1 cubic feet of concrete or grout. Convert to cubic yards: 66.1 ÷ 27 = 2.45 cubic yards.
- Block cost at the default $2.50 per block: 189 × $2.50 = $472.50 for the blocks. Mortar and fill are priced separately by your supplier and are not included in this figure.
So the finished shopping list for this wall is 189 blocks, 6 bags of 80 lb mortar, and — if the design fills every core — an order of about 2.45 cubic yards of concrete. If only some cores are filled, order proportionally less and confirm the exact cells with your mason before the truck is scheduled.
Quick reference tables
Speed sheetThe table below shows common wall sizes worked through the full formula, each including the 5% waste allowance, with mortar bags counted as 80 lb bags and fill assuming every core is filled
The table below shows common wall sizes worked through the full formula, each including the 5% waste allowance, with mortar bags counted as 80 lb bags and fill assuming every core is filled.
| Wall size | Blocks | Mortar bags (80 lb) | Core fill (all cores) |
|---|---|---|---|
| 10×4 ft garden wall | 48 | 2 | 0.62 cu yd |
| 20×8 ft | 189 | 6 | 2.45 cu yd |
| 30×8 ft | 284 | 9 | 3.68 cu yd |
Block sizes share the same face dimensions in most walls, which is why the block count stays the same even when the wall gets thicker. The differences below are in wall thickness and where each block is used.
| Block size | Face area | Notes |
|---|---|---|
| 8×8×16 in standard | 0.8889 sq ft | ~1.125 blocks per sq ft of wall |
| 4×8×16 in half block | 0.8889 sq ft | Half height, used for the top course |
| 12×8×16 in | Same face | Thicker wall, same block count |
What concrete blocks cost
At the national planning average of $2.50 per block, checked November 2026, the block cost for common walls breaks down like this: the 10×4 ft garden wall at 48 blocks runs about $120, the 20×8 ft wall at 189 blocks runs $472.50, and the 30×8 ft wall at 284 blocks runs about $710. These figures cover the blocks only.
Two things are not in these numbers. Mortar bags and core-fill concrete are priced separately, and both vary by brand, region, and delivery terms. Ready-mix suppliers also often apply minimum load charges on small orders like the 2.45 cubic yards needed for a 20×8 ft wall with all cores filled, which can raise the effective per-yard price.
Treat every figure here as a national planning range checked November 2026, never a quote. Block prices move with cement and freight costs and can differ noticeably by region and supplier. Get a current price from your local supplier before ordering, and keep the 5% waste allowance in your count so a price change or a few broken blocks don't force a second trip.
Frequently asked questions
How many blocks do I need for a 20×8 ft wall?
A 20 ft by 8 ft wall is 160 square feet. Dividing by the 0.8889 sq ft face of a standard block gives about 180 blocks, and adding the 5% waste allowance and rounding up gives 189 blocks. That count does not subtract openings, so if the wall has doors or windows, adjust the area first and recalculate.
Why does the calculator add 5% for waste?
Blocks chip in transit, crack during handling, and break while being cut for corners, top courses, and openings around doors and windows. Ordering the exact bare count almost always leaves you short. The 5% allowance covers that loss, and you can raise it if your wall needs heavy cutting or your supplier has a known breakage rate.
How many mortar bags do I need per 100 blocks?
An 80 lb bag of mortar mix lays about 33 blocks at standard joint thickness, so 100 blocks takes roughly 3 bags. The calculator divides your block count by 33 and rounds up. Walls with many half blocks, heavy cutting, or unusually wide joints consume mortar faster, so keep an extra bag on hand for those situations.
How much concrete does it take to fill block cores?
Each standard block holds about 0.35 cubic feet of concrete or grout when every core is filled. Multiply your block count by 0.35, then divide by 27 to get cubic yards. A 20×8 ft wall at 189 blocks works out to 66.1 cubic feet, or 2.45 cubic yards. Confirm which cores need fill before ordering.
Do I have to fill all the block cores?
No. Many walls only need fill in reinforced cells around vertical rebar, in bond beam courses, or in the bottom course. Filling every core in a 20×8 ft wall means 2.45 cubic yards of concrete, but a partially filled wall can need far less. Follow your structural plan and confirm the filled cells with your mason before scheduling delivery.
Does the block count change if I use a thicker block?
No. An 8×8×16 in standard block, a 4×8×16 in half block, and a 12×8×16 in block all present the same 0.8889 sq ft face, so the number of blocks per wall stays the same. The difference is wall thickness, which affects the width of the footing and the mortar spread, not the block count or the course layout.
Why does a half block have the same face area?
The 4×8×16 in half block is half the height of a standard block but is laid so its face covers the same 0.8889 sq ft footprint per course. It is typically used for the top course of a wall to finish the height without cutting full blocks. Your overall block count stays the same; the half blocks simply replace full blocks in that course.
Is the $2.50 per block price a quote?
No. The $2.50 per block default is a national planning range checked November 2026, never a quote. Actual block prices vary by region, brand, order size, and delivery fees, and they move with cement and freight costs. Use the calculator figure to estimate the block portion of your budget, then get a current price from your local supplier.
Assumptions and limitations
- Blocks are standard 8×16 in units with a face area of 0.8889 sq ft; other sizes change the count.
- The wall is a single wythe with no deductions for doors, windows, or other openings.
- A 5% waste allowance is applied to the block count, rounded up to whole blocks.
- One 80 lb bag of mortar lays approximately 33 blocks at standard joint thickness.
- Core fill assumes every core is filled, at 0.35 cu ft of concrete per block.
- Block cost uses the default $2.50 per block; mortar and fill are not included.
Sources
- National Concrete Masonry Association — ncma.org
- Portland Cement Association — cement.org
- The Home Depot — homedepot.com
- Lowe's — lowes.com
Last reviewed: November 20, 2026, by the YardMath Editorial Team. Formulas re-checked against manufacturer datasheets; national price ranges refreshed quarterly.